Easy instructions for replacing the ASK DP-6150 projector lamp

ASK DP-6150 projector, ASK Proxima LAMP-026
ASK DP-6150 projector
Follow our quick and easy step guide to installing a new ASK Proxima LAMP-026 projector lamp for your ASK DP-6150 projector.

Step 1: Finding the correct lamp

ASK DP-6150 lamp warning message, ASK LAMP-026
Lamp warning screen
ASK DP-6100 lamp replacement alarm, ASK LAMP-026
Lamp alarm

 

 

 

 

Watch for the warning messages on the ASK DP-6150 projector screen as well as the ALARM  on the projector light red. Either of these messages are indicators that the ASK LAMP-026 for your ASK DP-6150 projector must be replaced immediately.

Go with a genuine ASK LAMP-026 lamp

Be safe and get the best lamp for your ASK DP-6150 projector. Buy an authentic lamp from an authorized dealer that guarantees the ASK Proxima LAMP-026 you are installing will work in harmony with your projector. These genuine ASK Proxima LAMP-026 lamps have been manufactured with the correct materials and are designed to work properly with the intricate components in your ASK DP-6150 projector.

While the cheaper knock-off lamps sold at discount prices appear to be a smart bargain, they actually pose a danger to your health. Copy-cat manufacturers create these lamps are using toxic materials such as the cancer-causing compound Krypton 85 to get the same results since they don’t have access to the proper compounds. When these generic “compatible” lamps break or explode from overheating, anyone near the projector is exposed people to these toxic materials inside the lamp. Many generic lamps are also created without the proper safety device to protect your eyesight from UV light.Installing them also voids your projector warranty.

Protect your health and keep your projector warranty valid — buy an authentic ASK Proxima LAMP-026.

STEP 2: Replacing the ASK LAMP-026 projector lamp

IMPORTANT: Allow the ASK DP-6150 projector to fully cool down for at least one hour before replacing the ASK LAMP-026. These projectors operate under high heat and there is a seriousrisk of burning if the projector is not cooled enough.

ASK DP-6150 lamp cover, ASK LAMP-026To install a new ASK Proxima LAMP-026 lamp:

  • Gently turn over the ASK DP-6150 projector to access the lamp cage.
  • Loosen the 3 screws holding the ASK Proxima LAMP-026 lamp in place.
  • Grab the handle on the ASK Proxima LAMP-026 lamp cage and gently lift out the lamp. Place to one side.
  • IMPORTANT: These lamps contain mercury and must go to a local recycling program for proper disposal. Don’t throw used ASK LAMP-026 lamps into regular garbage! ASK DP-6150 lamp replacement, ASK LAMP-026
  • Take the new ASK Proxima LAMP-026 lamp. Don’t touch the bare bulb since the oil on your finger will burn a black mark on the lamp when the projector is turn on.
  • Place the ASK Proxima LAMP-026 into the projector.
  • Tighten the three screws on the new ASK Proxima LAMP-026 lamp.
  • Be sure to clean the filter.
  • You are ready to reset the Lamptimer.

 

STEP 3: Resetting the Lamptimer

It’s important to reset the Lamptimer after replacing the ASK Proxima LAMP-026 in the ASK DP-6150 projector in order that the lamp life be accurately tracked and recorded. Failure to do so may result in the lamp being used longer than it’s lamp life.

ASK DP-6150 lamp reset menu, ASK LAMP-026ASK DP-6150 replace lamp icon, ASK LAMP-026

 

To reset the Lamptimer:

  • Open the MAIN MENU. Press ENTER.
  • Scroll down to the SERVICE menu. Press ENTER.
  • Scroll down to the Reset lamptimer option. Press ENTER.
  • The lamptimer icon will appear to show you have reset the timer.

Leave A Comment?