Replace the Vizio E601i-A3 LED RUNTK5261TPZC T-Con board


There is nothing more disappointing than settling down to watch a favorite show and discover your TV is not working. That black screen on your Vizio E601i-A3 LED TV may be caused by a faulty T-Con board.

Some of the VIZIO’s E601i-A3 LED TVs are experiencing blackouts after being turned on. The problem is a 8 pin eprom chip failure on the lower right side of the RUNTK5261TPZC timing control board (T-Con) that interrupts the video signal to the Main board.

This T-Con board failure is happening at 500 hours of usage and according to VIZIO affects those E601i-A3 TVs with serial numbers in the ranges of LFTRNWAN3800001 to LFTRNWAN4805300.

If your VIZIO E601i-A3 is older than a year, your warranty will not cover the replacement costs for a new T-Con board. Fortunately the replacement RUNTK5261TPZC T-Con board is available for sale online for under $150.


Replace the RUNTK5261TPZC T-Con board

Equipment needed:

  • Antistatic plastic gloves or antistatic bracelet
  • Pad/ towel
  • Needle-nose pliers
  • Electric Flat head and Philips screwdriver
  • Cup for screws

Step-by-step instructions


  • Turn the VIZIO’s E601i-A3 television off. Unplug the power cord.
  • Remove the TV from the wall, if mounted.
  • Lay the VIZIO’s E601i-A3 TV on a flat, padded surface.
  • Remove the TV stand by loosening the screws at the base. Both the stand and post must be removed in order to remove the back panel.
  • Go to the back of the panel.
  • Remove all the screws holding the back panel in place. Put the screws to one side.
  • Remove the back panel.
  • The RUNTK5261TPZC T-Con board is located in the middle top of the back panel, usually under an aluminum cover held in place by four corner screws. It may also be held in place with foil tape at the top. It’s connected to the Main board through a black LVDS cable and flat ribbon cables.
  • Remove the ribbon cable first. Flip up the black tabs on the connector. Gently pull the cable out taking care not the scratch the ribbon section. Never use any sharp objects to open the black tabs as this can damage the pins making the connection faulty.
  • To remove the LVDS cable, squeeze the small tab on side. Don’t force anything apart or pull anything too hard as this can damage the connections and cause more problems.
  • Loosen the screws holding the RUNTK5261TPZC T-Con board in place. Place it to one side. This board is considered e-waste and should be sent to a recycling facility. Do not place into regular garbage.
  • NOTE: Be sure to put on your rubber gloves before touching the new T-Con board. Hold the RUNTK5261TPZC T-Con board by the edge and avoid touching any of the components since they are very sensitive to electrostatic charges.
  • Verify the manufacturers number for your board. (It will be found under the bar code.) Place the new board onto the back panel.
  • To re-install the ribbon cable: Match the line on the ribbon cable with the edge of the connector making sure the ribbon is straight. Press down on the tab to lock it into place.
  • Re-connect the LVDS cable by putting the connector end into the RUNTK5261TPZC T-Con board until it clicks into place.
  • Tighten the screws on the board. Replace any foil tape.
  • Replace the RUNTK5261TPZC T-Con cover. Tighten the screws.
  • Place the back cover back onto the VIZIO’s E601i-A3 TV and tighten all the screws.
  • Re-install the stand and post. Remount the VIZIO’s E601i-A3 TV.


Alternative part numbers

The RUNTK5261TPZC T-Con board is also sold under the following numbers:


  1. Edward Sage

    Hi was wondering will this T-Con board runtk5261tpzc fit my Vizio 60″ Model e-60i-a3 TV serial number Lftrnwbp 2906826?Having the same problems as many Vizio owners are having with their E-601i-A3 Vizio 60″ TV’s. Thanks so very much for your video & information on this problem. Sincerely Ed Sage

  2. George Deyo

    It seems there are other serial numbers for this problem with the Vizio E601i-A TV’s. My Son has the same issue as stated with the screen going black but still has audio. His Serial Number is
    LFTRNWDQ0203269. Vizio doesn’t care and their customer service basically says call a repair person to get it fixed. That’s the last Vizio product we purchase.

    1. Shelagh McNally

      Hi George,
      let me run this by our experts over at the forum and see what they have to say about replacing that T-Com board. We will get back to you shortly.

    2. scott

      I have the same problem and received the same answer from Vizio,”too bad.” I couldn’t be more disappointed in this company and their customer service. I’ll never buy another Vizio and have actually gone out of my way to tell others the same.

  3. Bumpy

    Vizio E601i-A3 LED has a green line through screen.
    How do I fix this problem?

    1. Shelagh McNally

      Hi Bumpy,
      That sounds like your color ballast that needs to be replaced. There are experts over at the forum that can help.
      Check out the discussion boards there for more help.

  4. kevin kamp

    re vizio e601i-a3, would like to replace the 8 pin eprom on tcon board you idenified. can you forwad specific info on it. thankyou, Kevin.

    1. Shelagh McNally

      Hey Kevin,
      I’ve asked one of our forum experts to contact you and get you the right leads for the Tcon board you need.

  5. Ron

    I have a E601i-A3 that went black screen on me. Sound was still working. I replaced the RUNTK5261TPZC T-Con board, no luck, still a black screen. Did I miss something?

    Also I found the T-con board to be located on the bottom middle backside of the TV (instead of top middle).

    1. Shelagh McNally

      Hi Ron,
      This is too complicated a problem for me to comment on. I suggest heading over to our forum: I’ll send this message to one of our experts there and see if he can help.

    2. Adam Torres

      I have the same problem, did you ever get yours fixed?

  6. Adam Torres

    I replaced the t con board with one I bought from shopjimmy and I still get no picture. Screen lights up but no picture.

    1. Shelagh McNally

      Hi Adam,
      Did you check the lamp and reset the lamp timer. You usually have to replace the lamp after changing the t-con board. I’m not an expert so I would recommend heading over to our forum where there are more experts to help. They can help you solve this problem.

Leave a Reply to George Deyo Cancel Reply