How to install a new Optoma EP7475 projector lamp

Replacing the Optoma EP7475 projector doesn’t have to be time consuming or difficult. This quick guide will help you install a new Optoma BL-FP230A lamp in less than 15 minutes.

Optoma_EP7475_projectors_Optoma_BL-FP230A_projector_lamp

When the Optoma BL-FP230A (SP.83R01G001) lamp is reaching end of life, the Lamp Replacement message will appear on screen. You should prepare to change the lamp as you 30 hours or less before the projector shuts down.

Be prepared, buy authentic

Be sure to buy an authentic an Optoma BL-FP230A (SP.83R01G001) lamp for the Optoma EP7475 projector. Scroll down for the 6 reasons to avoid generics.

 

Step-by-step instructions

Follow these safety steps before installing the new Optoma BL-FP230A (SP.83R01G001) lamp:

  • Switch off the power to the Optoma EP7475 projector by pressing the Power/Standby button.
  • Disconnect the power cord.
  • Allow the projector to cool down for at least 30 minutes. If should be cool to the touch. These projectors run using high temperatures and you can burn yourself badly if you don’t allow the projector to cool down.

Lamp_Replacement_Remove_screws_Optoma_BL-FP230A_projector_lamp_projector_EP7475

 

Using a screwdriver, remove the screws holding the cover in place.

Replacement_remove_cover_Optoma_BL-FP230A_projector_lamp_Optoma_EP7475_projector

Push the cover up to remove.

 

 

 

 

EP7475_Lamp_Replacement_remove_lamp_screws_Optoma_BL-FP230A_projector_lamp

 

Use a screwdriver to remove the two screws holding the lamp module in place.

Slowly put out the old lamp by grabbing the edge of the lamp. Be careful not to bang the lamp against the projector as this may case the bulb to break. Learn what to do if the lamp has exploded inside the projector.

Note: The used Optoma BL-FP230A (SP.83R01G001) lamp contains mercury and should be r properly recycled. Don’t throw it into regular garbage.

 

 

Optoma_EP7475_projector_remove_ BL-FP230A_lamp

 

Place the new BL-FP230A (SP.83R01G001) into the Optoma EP7475 projector. Tighten the two screws on the lamp. Replace the lamp cover and tighten its two screws.

You must now reset the Lamp Replacement Timer.

 

 

 

Reset the lamp timing on the Optoma EP7475

The Optoma EP7474 projector has an automatic lamp reset timer that tracks the life of the lamp and triggers the lamp replacement warning. You need to reset the timer each time the lamp is replaced.

Optoma_EP7475_projector_Lamp_Control_Menu_Optoma_BL-FP230A_projector_lamp

 

  • Press the Menu option on either the remote or on the projector.
  • Scroll over the Lamp Setting. Press enter.
  • Select Reset Lamp Hours. Press Enter
  • The Execute/Cancel command line will appear.
  • Scroll over to choose Execute. Press Enter.
  • The lamp hours will be reset to zero.

Extend the life of the Optoma BL-FP230A (SP.83R01G001) lamp by:

  • Turning on the Eco Mode to lower power consumption and extend the lamp life by 130%.
  • Keep your air filters clean to avoid overheating the projector.
  • Turn off the Optoma EP7475 projector and let it stand for at least one hour ever 24 hours.
  • Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
  • Learn more with Top tips for extending DLP projector lamp life

6 reason to avoid generics:

Learn the 7 Ways to Spot a Counterfeit Lamp.

 

Leave A Comment?