Install a new BenQ MX761 projector lamp

BenQ _MX761_projector_5J.J3J05.001_projector_lampReplace the BenQ 5J.J3J05.001 projector lamp in your BenQ MX761 projector in three easy steps.

Step 1: Warning signs for end of projector lamp

When the BenQ 5J.J3J05.001 is reaching end of life the lamp indicator on the BenQ MX761 projector will start flashing orange. Warning messages will also begin to appear on screen. You may notice the image deteriorating or the color looking off. Check how low the lamp has left: BenQ-_MX761_projector_5J.J3J05.001_projector_lamp_warning

  • Press MENU/EXIT and then press MODE/ENTER to highlight the SYSTEM SETUP: Advanced
  • Press to highlight Lamp Settings and press MODE/ENTER. The Lamp Settings page is displayed.
  • You will see the Equivalent Lamp Hour information appearing on the menu.
  • To leave the menu, press MENU/EXIT.
  • You can also get the lamp hour information on the INFORMATION menu.

Setting the projector to economic mode will extend the projector lamp life.

Step 2: Be ready with an authentic projector lamp

Keep your BenQ MX761 projector working at its optimum levels by always using an authentic BenQ 5J.J3J05.001 projector lamp for your BenQ MX761 projector. Generic lamps may promise to work just as well but they don’t and end up costing you more money in the end.

6 reasons to go with authentic projector lamps:

Step 3: Replace the BenQ 5J.J3J05.001 projector lamp

Before changing the lamp:

  • Reduce the risk of electrical shock by disconnecting the power cord on the BenQ MX761 projector.
  • Reduce the risk of severe burns by allowing the projector to cool for at least 45 minutes.

BenQ-_MX761_projector_5J.J3J05_projector_lamp_remove_cover_screw

 

Loosen the screw holding the lamp cover onto the BenQ MX761 projector.

BenQ-_MX761_projector_5J.J3J05_projector_lamp_remove_cover

Lift up the cover. Remove and dispose of the lamp protection film. Do not insert your fingers between the lamp and the projector. The sharp edges inside the projector may cause injuries.

 

BenQ-_MX761_projector_5J.J3J05_disconnect_projector_lamp

Disconnect the projector lamp connector from the projector (Step #2). Loosen the screw that secures the BenQ 5J.J3J05.001 projector lamp.

BenQ-_MX761_projector_5J.J3J05_remove_old_projector_lampSlowly and gently pull the BenQ 5J.J3J05.001 projector lamp out of the projector. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The BenQ 5J.J3J05.001 projector lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps! If you bought from an authentic manufacturer they will recycle the lamp for you at no extra cost (another reason to buy authentic lamps).

 

BenQ-_MX761_projector_5J.J3J05_install_new_projector_lampInsert the new BenQ 5J.J3J05.001 projector lamp first into the connector on the projector and reconnect the lamp connector.

BenQ-_MX761_projector_5J.J3J05_tighten_projector_lamp_screw

Make sure the handle is fully locked. Tighten the projector lamp screw. If the screw is too loose or too tight, the projector may not turn on.

BenQ-_MX761_projector_5J.J3J05_projector_lamp_install_coverRe-install the BenQ MX761 lamp cover and tighten the screw. Reset the total lamp operation timer.

 

Reset the projector lamp counter

BenQ-_MX761_projector_5J.J3J05_reset_projector_lamp_timerWhen the BenQ 5J.J3J05.001 projector lamp in the BenQ MX761 projector has been changed the projector lamp timer must be reset:

  • Turn on the BenQ MX761 projector.
  • After the startup logo, open the On-Screen Display (OSD) menu.
  • Go to the SYSTEM SETUP.
  • Scroll over to Advanced > Lamp Settings menu.
  • Press MODE/ENTER to display Lamp Settings page is displayed.
  • Highlight Reset lamp timer. A warning message is displayed asking if you want to reset the lamp timer.
  • Highlight Reset and press MODE/ENTER. The lamp time will be reset to “0”.

Extend the life of the BenQ 5J.J3J05.001 projector lamp last longer with the following tips:

  • Keep your air filters clean to avoid overheating the projector.
  • Use the Lamp Power option on the MX761 projector lamp and set to Economic Mode to reduce the amount of power used but extend lamp life.
  • Learn more with Top tips for extending DLP projector lamp life.

BenQ-MX760_projector_5J.J3J05_projector_lamp_Video_guide

Green your BenQ MX761 projector lamp

The BenQ MX761 projector lamp has the option of replacing only the bulb in the BenQ 5J.J3J05.001 projector lamp. You re-use the plastic cage and reduce waste. You can green your projector while saving money. Our instructional video shows you how step-by-step.

 

 

Leave A Comment?