Install a new Optoma DX319 projector lamp

Optoma_DX319_Optoma_BL-FU185A_SP.8EH01GC01_projector_lampReplace the Optoma DX319 projector lamp with help from our user guide.

Invest in authentic replacement projector lamps

Note: These instructions can also be used with the Optoma DX319P projector.

Be sure to have your back-up replacement Optoma BL-FU185A (SP.8EH01GC01) projector lamp ready so you can replace it immediately when needed. When buying on the Internet, make sure you are buying an OEM and look for the seal of approval. Generic lamps have a shorter lamp life than original lamps and are created with toxic materials. When you buy copy-cat lamps you get no guarantee or refunds and they can damage the sensitive electronics in your projectors. Keep your Optoma DX319 projector working at its best! Learn How to spot a counterfeit.

End of life warnings

Optoma_DX319_Optoma_BL-FU185A_SP.8EH01GC01_replacement_warning_projector_lampWhen the Optoma BL-FU185A projector lamp is reaching end of life, you will notice the Lamp-LED light flashing red on the Optoma DX319 projector. A lamp warning message also appears on screen.

If you hear a loud pop when turning on the projector, the Optoma BL-FU185A (SP.8EH01GC01) projector lamp has broken. Learn what to do if the projector lamp has exploded inside the projector.

4-steps to installing the Optoma BL-FU185A projector lamp

Follow these important safety tips before replacing the Optoma BL-FU185A (SP.8EH01GC01) projector lamp:

  • Switch off the power to the Optoma DX319 projector by pressing the Power/Standby button.
  • Disconnect the power cord.
  • Allow the Optoma DX319 projector to cool down for at least 30 minutes. These projectors run using high temperatures and you can burn yourself badly if you don’t allow the projector to cool down.

Optoma_DX319_Optoma_BL-FU185A_SP_projector_lamp_warningSteps to remove the old projector lamp

1. Use a screwdriver to undo the two screws holding the projector lamp cover in place. The screws on the lamp cover and the lamp cannot be removed.

2. Remove the lid and place to one side. Don’t lose the lid as the Optoma DX319 projector will not turn back on until the lamp cover has been properly installed.

3. Remove the two screws holding the Optoma BL-FU185A (SP.8EH01GC01) projector lamp in place.

Note: The used Optoma BL-FU185A (SP.8EH01GC01) projector lamp contains mercury and should be properly recycled. Don’t throw it into regular garbage.

4. Lift up the wire handle on the Optoma BL-FU185A (SP.8EH01GC01) projector lamp and slowly remove it from the projector. Be careful not to bang the lamp against the projector as this may case the bulb to break. Learn how to clean up a broken lamp.

Steps to install the new projector lamp:

1. Remove the new Optoma BL-FU185A (SP.8EH01GC01) projector lamp from its packaging. Taking care not to touch the actual bulb, lift up the handle on the new lamp and insert it gently into the Optoma DX319 projector.

2. Tighten the two screws on the projector lamp.

3. Replace the lamp cover and tighten its two screws.

4. Reset the lamp replacement timer

Reset the Projector Lamp Replacement Timer

Optoma_DX319_Optoma_BL-FU185A_SP_projector_lampThe Optoma DX319 multimedia projector has an automatic projector lamp timer that tracks the numbers of hours left in the lamp. If you don’t reset the lamp replacement timer you run the risk of the lamp being used beyond its recommended life and possibly exploding in the projector.

To reset the Projector Lamp Replacement Timer:

  • Turn on the projector.
  • Using the remote press MENU
  • Select OPTIONS
  • Select LAMP SETTINGS
  • Select LAMP RESET
  • Select YES.
  • Press MENU to exit.

Tips for extending Optoma BL-FU185A (SP.8EH01GC01) projector lamp life:

  • Chose the “STD” mode to to dim the projector lamp and lower power consumption. This will extend the lamp life by up to 130%.
  • Keep your air filters clean to avoid overheating the projector.
  • Every 24 hours, turn off the projector and let it stand for 1 hour
  • Make sure there is enough airflow around the Optoma DX319 projector particularly if it’s been permanently mounted.
  • Learn more with Top tips for extending DLP projector lamp life.

Green your Optoma DX319 projector

Optoma-BL-FU185A_replacement_bulb_training_videoThe Optoma DX319 projector has the option of re-using the existing lamp cage and replacing only the actual bulb. A great way to reduce and recycle. Watch our Optoma BL-FU185A training video to learn more.

Leave A Comment?