How to replace the BenQ MX762ST projector lamp

BenQ _MX762ST_projector_5J.J3J05.001_projector_lampThis step-by-step user guide walks you through replacing the BenQ MX762ST projector lamp in 3 easy steps.

NOTE: These instructions are also good for the BenQ MX762 projector.

Step 1: Be ready with an authentic projector lamp

It can be tempting to spend less and install a generic lamp bought at a discount place or over the Internet. However, to keep your BenQ MX762ST projector working at its optimum levels you should always use an authentic BenQ 5J.J3J05.001 projector lamp. Generic lamps may promise to work just as well but they don’t and end up costing you more money in the end.

6 reasons to go with authentic projector lamps:

Step 2:

A flashing orange light on BenQ MX762ST projector indicates that the t BenQ 5J.J3J05.001 is reaching end of life the lamp indicator and needs to be replaced. Several warning messsages will begin to appear and you may notice the image deteriorating or the color looking off. When the final warning screen appears you must change the projector lamp immediately.

To check how  many hours the projector lamp has, do the following: BenQ-_MX762ST_projector_5J.J3J05.001_projector_lamp_warning

  • Press MENU/EXIT and then press MODE/ENTER to highlight the SYSTEM SETUP: Advanced
  • Press to highlight Lamp Settings and press MODE/ENTER. The Lamp Settings page is displayed.
  • You will see the Equivalent Lamp Hour information appearing on the menu.
  • To leave the menu, press MENU/EXIT.
  • You can also get the lamp hour information on the INFORMATION menu.

Setting the projector to economic mode will extend the projector lamp life.

Step 3: Replace the BenQ 5J.J3J05.001 projector lamp

Before changing the lamp:

  • Reduce the risk of electrical shock by disconnecting the power cord on the BenQ MX762ST projector.
  • Reduce the risk of severe burns by allowing the projector to cool for at least 45 minutes.

BenQ-_MX762ST_projector_5J.J3J05_projector_lamp_remove_cover_screw

 

Loosen the screw holding the lamp cover onto the BenQ MX762ST projector.

BenQ-_MX762ST_projector_5J.J3J05_projector_lamp_remove_cover

Lift up the cover. Remove and dispose of the lamp protection film. Do not insert your fingers between the lamp and the projector. The sharp edges inside the projector may cause injuries.

 

BenQ-_MX762ST_projector_5J.J3J05_disconnect_projector_lamp

Disconnect the projector lamp connector from the projector (Step #2 in diagram). Loosen the screw that secures the BenQ 5J.J3J05.001 projector lamp.

BenQ-_MX762ST_projector_5J.J3J05_remove_old_projector_lampSlowly and gently pull the BenQ 5J.J3J05.001 projector lamp out of the projector. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.

NOTE: The BenQ 5J.J3J05.001 projector lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps! If you bought from an authentic manufacturer they will recycle the lamp for you at no extra cost (another reason to buy authentic lamps).

 

BenQ-_MX762ST_projector_5J.J3J05_install_new_projector_lampInsert the new BenQ 5J.J3J05.001 projector lamp first into the connector on the projector and reconnect the lamp connector.

BenQ-_MX762ST_projector_5J.J3J05_tighten_projector_lamp_screw

Make sure the handle is fully locked. Tighten the projector lamp screw. If the screw is too loose or too tight, the projector may not turn on.

 

BenQ-_MX762ST_projector_5J.J3J05_projector_lamp_install_coverRe-install the MX762ST  lamp cover and tighten the screw.

Reset the total lamp operation timer.

 

 

Reset the projector lamp counter

BenQ-_MX762ST_projector_5J.J3J05_reset_projector_lamp_timerWhen the BenQ 5J.J3J05.001 projector lamp in the BenQ MX762ST projector has been changed the projector lamp timer must be reset:

  • Turn on the BenQ MX761 projector.
  • After the startup logo, open the On-Screen Display (OSD) menu.
  • Go to the SYSTEM SETUP.
  • Scroll over to Advanced > Lamp Settings menu.
  • Press MODE/ENTER to display Lamp Settings page is displayed.
  • Highlight Reset lamp timer. A warning message is displayed asking if you want to reset the lamp timer.
  • Highlight Reset and press MODE/ENTER. The lamp time will be reset to “0”.

Extend the life of the BenQ 5J.J3J05.001 projector lamp last longer with the following tips:

  • Keep your air filters clean to avoid overheating the projector.
  • Use the Lamp Power option on the MX761 projector lamp and set to Economic Mode to reduce the amount of power used but extend lamp life.
  • Learn more with Top tips for extending DLP projector lamp life.

BenQ-MX762ST_projector_5J.J3J05_projector_lamp_Video_guide

Green your BenQ MX762ST projector lamp

The BenQ MX762ST projector projector lamp has the option of replacing only the bulb instead of the entire BenQ 5J.J3J05.001 unit. You re-use the plastic cage and reduce waste. You can green your projector while saving money. Our instructional video shows you how step-by-step.

 

 

Leave A Comment?